When used as described, the emergency stop switch and lanyard system stops the engine if the operator falls away from the controls. We help you get the job done by getting you the right parts at discount prices up to 80 percent off retail, and we ship your parts fast so you can get to work. Start the engine and check for leaks. After draining thoroughly, tighten the drain bolt securely. Remove it by unscrewing it and replacing. Stop the engine immediately if anyone falls overboard, and do not run the engine while the boat is near anyone in the water. The Star Label means Cleaner Marine Engine This engine has been certified as a: The Symbol for Cleaner Marine Engines: Cleaner Air and Water - for healthier lifestyle and environment.
Got a problem with your Honda outboard? Running the outboard motor without suf f icient cooling water will damage the water pump and overheat the engine. Drain the fuel tank into an approved gasoline container, or if you need to store fuel in the fuel tank, you can extend fuel storage life by filling the fuel tank with fresh gasoline and adding a fuel. We suggest that you stop the engine this way occasionally to verify that the engine and emergency stop switch is operating properly. These gasolines are collectively referred to as oxygenated fuels. That way, you can get to work, finish the job, put down the tools, and get back on the water. When the boat is to be moored for a long time, tilt the outboard motor as far as it will go.
Shop Manual This manual covers complete maintenance and overhaul procedures. Adjust the trim tab in small increments, and retest steering effort with the boat evenly loaded and running at cruising speed. You can follow me at these other sites as well: Facebook - Twitter - Instagram - YouTube - Good Fishing! The propeller blades may have sharp edges, so wear heavy gloves to protect your hands. Remove the dipstick and wipe it clean. If no water or sediment are found, reinstall the fuel filter properly. If you are looking for Honda 130 Outboard Motor Boat Parts, you have indeed come to the proper place.
However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. So, whether it's the parts, the motors, or even the boats themselves, Boats. Unlock and remove the engine cover p. Use the minimum throttle opening necessary to operate the boat at a safe trolling speed. Unlock and remove the engine cover p. Above 41°F 5°C , warm up the engine for 2 or 3 minutes.
Install the drain hose to the silencer case. Take outboard motor to an authorized Honda Marine dealer, or refer to the shop manual. After the outboard motor is placed in storage and disconnected from the hoist, install the engine cover. Before use, open the fuel tank vent by turning the vent knob at least 2 or 3 turns counterclockwise. Running the engine without water can cause serious engine damage. If you are at cruising speed, engine speed will decrease gradually.
Use 4-stroke automotive detergent oil. Before starting the engine, hold the priming bulb up in the direction of the arrow, then squeeze the priming bulb until it feels firm. It may also damage metal, rubber, and plastic parts of your fuel system. Remove any portable fuel tank from the boat for refueling. When you click the diagrams, you can identify the parts you need and you can also see how the parts fit together in your engine. In this article we will go over the simple steps of changing the engine oil in Honda four-stroke outboard motors.
Keep the portable fuel tank away from the battery or other potential spark sources. Make sure you snug it up tight. They are made of a sacrificial material and help protect the outboard motor from corrosion. Less friction allows easier control lever movement. Bad fuel; boat stored without treating or draining gasoline, or refueled with bad fuel. The control lever automatically locks itself in the N neutral position.
Only you can decide whether or not you should perform a given task. To adjust, first tilt the outboard motor so it is not resting on the rod. If the engine protection system remains activated after 30 seconds, return to the nearest boat landing, and have the outboard motor inspected by an authorized Honda marine dealer. The engine will not start if the F forward or R reverse gears are engaged. With a little simple maintenance, these Honda outboards will last for many years of tireless use.
I pulled the dip stick and found it to be a lite brown milky color and it smells of fuel. Water or sediment accumulated in the filter can cause loss of power or hard starting. I don't want to get my self into a major headache with this motor but the boat is a killer deal. Simply click on your outboard's model and you'll be taken to the parts page for that exact motor. Once you identify your motor, you can use the exploded Honda outboard parts diagrams. If the gasoline in your fuel tank and vapor separator deteriorates during storage, you may need to have the vapor separator and other fuel system components serviced or replaced. So regardless if this is one part or a whole bunch of them, getting original Honda marine parts helps you keep your outboard in top performance.
The water separator red float has risen off the bottom of the bowl Spark plugs faulty, fouled or. If loss of power or hard starting are found to be caused by excessive water or sediment accumulation in the fuel filter, inspect the fuel tank. Disconnect the outboard motor from the boat, hoist the outboard motor, and move it to the storage area. Proper adjustment prevents the outboard motor from being trimmed too low p. Engine overheating may be the result of clogged water intakes.